Get Dasca

Docs

Learn Dasca, from your first project to node graphs.

Effects / Audio and Signals

Audio and Signals

Drive effect sliders with audio bands, levels and generated waves from the Signals tab, with range remap and smoothing.

Note

These docs cover Dasca 2.3.

Signals move effect sliders automatically. A signal can come from audio (an imported audio file or the soundtrack of your video) or from a built-in generator such as a sine wave. You connect a signal to a slider and choose the range it moves in.

Where to find it

Open the Signals tab at the top of the right panel, next to Effects. Signals are available in Effects mode only, for images, video and 3D models. Kinetic, Code and Node modes do not use them.

The tab has four parts: the audio box, the Audio signals, the Generated signals and Connections. The Audio, Generated and Connections sections can be collapsed.

Audio source

With no audio loaded, the audio box shows two buttons:

ButtonWhat it does
Import audioLoads an audio file: MP3, WAV, OGG, FLAC, M4A, AAC or WMA.
Use video audioUses the soundtrack of the imported video. Available only when a video is loaded. It also unmutes the video.

When audio is loaded, the box shows:

  • Play / Pause, Stop (rewinds to the start) and Loop on / Loop off, for an imported audio file. For video audio, playback follows the video transport.
  • The file name, or Video audio for the soundtrack.
  • A position bar you can click or drag to seek, with the current time and length.
  • Mute / Unmute and a Volume slider (0% to 100%).
  • Remove audio (or Stop using video audio) to unload the source.

Audio signals

Audio signals analyze the loaded audio while it plays. Each card shows a live ring meter.

SignalWhat it follows
BassEnergy in the 20 to 250 Hz band.
MidEnergy in the 250 to 4000 Hz band.
TrebleEnergy in the 4000 to 20000 Hz band.
LevelOverall loudness (RMS level).
PeakPeak amplitude.
TransientSudden hits and onsets, such as drums.

Audio signals need loaded audio. Without audio they stay at rest.

Generated signals

Generated signals need no audio. Each card shows a live preview of the wave.

SignalShapeParameters
SineSmooth up and down waveRate, Phase
SawRising ramp that drops backRate, Phase
TriangleLinear up and downRate, Phase
SquareSwitches between low and highRate, Phase
NoiseRandom valuesRate
EnvelopeRepeating rise and fallRate, Atk, Rel
Random WalkSlow wandering valueSpeed, Damp
ParameterRangeDefaultWhat it does
Rate (Sine, Saw, Triangle, Square)0.01 to 10 Hz0.5 HzCycles per second.
Phase0° to 360°0°Shifts the wave in time.
Rate (Noise)0.1 to 20 Hz4 HzHow often the value changes.
Rate (Envelope)0.01 to 5 Hz0.5 HzHow often the envelope repeats.
Atk10 to 2000 ms200 msRise time of the envelope.
Rel10 to 3000 ms400 msFall time of the envelope.
Speed0.05 to 30.5How fast the random walk moves.
Damp0.5 to 0.990.85Damping of the random walk.

Smoothing

Click a signal card to select it. Knobs for that signal appear under the grid:

KnobRangeWhat it does
Smooth0% to 100%How gradually the signal follows changes. 0% reacts at once, 100% is very slow. Setting Smooth also resets Attack and Release to match it.
Attack0.05 to 0.95Rise time. Lower values react faster when the signal increases.
Release0.05 to 0.98Fall time. Higher values decay more slowly when the signal decreases.

Generated signals show their own parameters next to these knobs. Double-click any knob to reset it. Each signal has its own default Smooth value, for example 60% for Bass and 35% for Transient.

Connecting a signal to a slider

  1. Select an effect in the Effect Chain. The selected effect is the target.
  2. In the Signals tab, hover a signal card and click the link button.
  3. Pick a slider from the list. Only slider parameters can be connected.

A colored dot on a card means that signal is connected. The connection starts with a range from 25% to 75% of the slider range.

In the effect settings, a connected slider shows colored dots next to its label. Click them to open a Connections list, where you can disconnect each signal.

You can connect several signals to the same slider, and one signal to several sliders.

Connections and range remap

The Connections section lists every connection as "signal → slider". Each row has:

  • A two-thumb range slider. The signal moves the effect slider between the low and high value. Drag a thumb to change one end, or drag the colored bar to move the whole range.
  • Mapped minimum and Mapped maximum value fields for exact numbers.
  • Hide connection / Show connection (eye) to turn a connection off without deleting it.
  • Remove connection (X).

Clear all in the section header removes every connection after you confirm with Yes.

Export

Connections are baked into video export frame by frame, so the motion in the file matches the preview. When connections are active, the export dialog defaults to video, and a 3D scene with active connections can be exported as video. Turn on Include audio to add the soundtrack to the file (not available for GIF). See Video Export.

Signals cannot be changed while an export is running.