Layers and Masks
Blend modes, opacity and masks for each effect in the Effect Chain, including luma, linear and radial masks and the mask view.
These docs cover Dasca 2.3.
Every effect in the Effect Chain has a Layer section and a Mask section in its settings. Layer controls how the effect mixes with the image it receives, and Mask controls where the effect appears.
Where to find them
Select a chip in the Effect Chain bar. The Layer and Mask sections are at the bottom of the effect's settings panel, under Settings (and Transform, if the effect has one). They appear only for effects that are part of the chain. When you work with a single effect, add a second effect to get them.
Each chain effect works on the image coming from the effect before it (for the first effect, your source). In this page that incoming image is called "the image below".
Layer
| Control | Range | Default | What it does |
|---|---|---|---|
| Blend | See the list below | Normal | How the effect's result is combined with the image below. |
| Opacity | 0 to 100 | 100 | How much of the blended result you see. At 0 the effect is invisible, at 100 it is fully applied. |
The current opacity is also shown on the effect's chip in the chain bar.
Blend modes
| Blend | What it does |
|---|---|
| Normal | The effect's result replaces the image below. |
| Multiply | Multiplies the two images. The result is always darker; white in the effect leaves the image below unchanged. |
| Screen | The opposite of Multiply. The result is always lighter; black in the effect leaves the image below unchanged. |
| Overlay | Increases contrast. Dark areas of the image below get darker and light areas get lighter, depending on the effect. |
| Soft Light | A gentler version of Overlay. The effect lightens or darkens the image below softly. |
| Add | Adds the two images. Bright areas of the effect brighten the result and can clip to white. |
| Difference | Shows the difference between the two images. Identical areas turn black, different areas show bright colors. |
Mask
A mask limits the effect to part of the image. Where the mask is white the effect is fully applied, where it is black you see the image below, and gray values give a partial mix. The mask works together with Opacity.
Turn the mask on with the switch in the Mask section header (tooltip "Turn mask on"). While the mask is off you can still open the section to look at its settings; they are dimmed and have no effect until you turn the mask on.
Mask types
| Type | What it does |
|---|---|
| Luma (below) | Uses the brightness of the image below. The effect appears only in a chosen brightness range of the incoming image. |
| Luma (effect) | Uses the brightness of the effect's own result. The effect appears only where its own output falls in the chosen brightness range. |
| Linear | A straight edge across the canvas. The effect fades in from a center line toward the direction set by Angle. |
| Radial | A circle. The effect is applied inside the circle and fades out past its edge. |
The default type is Luma (below).
Mask controls
The controls shown depend on the type.
| Control | Types | Range | Default | What it does |
|---|---|---|---|---|
| Type | All | Luma (below), Luma (effect), Linear, Radial | Luma (below) | Chooses how the mask is made. |
| Range (Low, High) | Luma | 0 to 1 each | 0.25, 0.75 | Brightness range where the effect appears. 0 is black, 1 is white. |
| Softness | Luma | 0.01 to 0.35 | 0.08 | How soft the edges of the brightness range are. Higher values give smoother transitions. |
| Center (X, Y) | Linear, Radial | 0 to 1 each | 0.5, 0.5 | Position of the mask on the canvas. 0.5, 0.5 is the middle. |
| Angle | Linear | -180 to 180 | 90 | Direction of the linear mask in degrees. |
| Radius | Radial | 0 to 1.5 | 0.35 | Size of the circle, measured against the canvas height. |
| Feather | Linear, Radial | 0 to 1.5 | 0.2 | Width of the soft transition. For Linear it is the fade distance from the center line, for Radial the fade distance outside the circle. Measured against the canvas height. |
| Amount | All | 0 to 1 | 1 | Strength of the mask. At 1 the mask is fully used; at 0 the mask has no effect and the effect shows everywhere. |
| Invert | All | On/Off | Off | Swaps the masked and unmasked areas. |
The Range control
For the luma types, Low and High are combined into one Range row:
- Drag the Low or High field left or right to change it, or click it to type a value.
- Below the fields is a black-to-white strip with a curve that shows the mask: the higher the curve, the more of the effect you see at that brightness. The curve also reflects Softness, Amount and Invert.
- Drag an end of the strip to move that end of the range. Drag the middle to move the whole range. Hold Shift for fine steps. Double-click the strip to reset it to the defaults. Press Esc while dragging to cancel.
Typical uses:
- Low around 0.6 and High at 1: the effect appears only in highlights, for example grain or glow on bright areas.
- Low at 0 and High around 0.4: the effect appears only in shadows.
- Turn on Invert to protect a brightness range instead of targeting it.
Mask handles on the canvas
For Linear and Radial masks, handles appear on the canvas while the mask is on and the effect is selected:
| Handle | Type | What it does |
|---|---|---|
| Mask Center | Linear, Radial | Drag to move the mask. Sets Center. |
| Mask Angle | Linear | Drag around the center to rotate the mask. Sets Angle. |
| Feather | Linear | Drag to widen or narrow the fade. Sets Feather. |
| Radius | Radial | Drag to resize the circle. Sets Radius. |
| Feather | Radial | Drag the outer ring to change the fade. Sets Feather. |
Double-click a handle to reset its value. Handle details and modifier keys are on Transform and Gizmos. Press G to hide or show handles.
Mask view
To see the mask itself, click the View mask button in the Mask header, or Alt+click (Option+click on macOS) the Mask title. The canvas then shows the mask of the selected effect in grayscale: white where the effect is applied, black where it is not. Click the button again (tooltip "Back to image") to return to the normal view.
Mask view is available only while the mask is on. It is a preview aid and does not change your export.
Keyframes
Opacity, Blend and the mask values (Type, Range, Softness, Center, Angle, Radius, Feather, Amount, Invert) can be keyframed. Sliders animate smoothly; Blend, Type and Invert switch at the keyframe. The mask on/off switch and the effect's on/off state are not keyframed. See Keyframes and Timeline.